Washing machine won’t spin just one item or very small load

laundry still wet Many people are having issues with new washing machines that refuse to spin just one item, or maybe just a few items. Sometimes it may have been a reasonably sized load in their old washing machine but they’ve now bought one with a large capacity drum so the load is still relatively small.

They are frustrated because their previous washing machine would spin with just one item inside but their new one won’t, and they are convinced the washing machine is faulty. Although faults can occur, it’s now normal for a washing machine not to spin just one or two items, or even some small loads, especially if one or more of the items gets heavy when wet such as a large woollen cardigan, a thick cotton garment or a heavy bath mat.


Why can’t modern washing machines just spin anything I put in the washing machine?

They did used to, but when washing machines were designed to just get on with spinning after a couple of minutes trying to balance the load there were consequences.

Every so often a load would be a little out of balance (especially when mixing light and heavy items or if there wasn’t enough items to stick evenly all round the drum) but the washing machine would go into spin regardless.

This often caused the washer to give a good thump several times as it ramped into spin before settling down often with a few more thumps occurring right at the end of the spin. It was disconcerting but usually just resulted in the sides of the washing machine being dented.


More rarely sheets would tangle up, or a small load would be impossible to balance and contain one or more heavy items such as a few towels, a sheet or one heavy garment and the washing machine would go seriously crazy. As a repairman in these days it was very common to see washing machines destroyed by being left unattended with an unbalanced load which had spun out of control for the full spin cycle.

If you’ve ever been close to a washing machine leaping into spin with a badly balanced load it is quite frightening. Customers used to describe watching TV in the lounge and being terrified by the sound of someone apparently battering their back door down.

I’ve seen hundreds of washing machines written off because the tub inside went out of control and smashed the control timer, yanked off hoses resulting in flooding all the motor or electrics, or simply broke the vitreous enamel tub suspension bracket with the sheer forces involved.


I’ve seen floorboards splintered with holes punched right through as the suspension rod repeatedly pummelled the floor and I’ve seen washing machines walk across the kitchen, jump up and smash cupboard and worktops etc. This state of affairs was clearly unacceptable, and something needed to be done about it.

The Answer they came up with is out of balance protection

The out of balance protection is a modern idea to stop washing machines going into spin with unbalanced loads. Early versions were crude, and simply attached micro switches to the tub or suspension, which when triggered through violent tub swinging just cut the motor to limit the damage done.

Modern out of balance protection is commonly achieved using software monitoring the strains on the motor through the power it uses. If a load is evenly distributed around the inner drum the motor should run fairly smoothly as it turns it round requiring a pretty even amount of power. If one side of the drum is heavier than the other, which would happen with only a few small items or one garment inside it would create imbalance.


The motor would run unevenly as it encountered different physical resistance when it turned the heavy side of the drum up from the 6 O’clock position through past 12 O’clock compared to the lighter load (or no load at all) on the other side.

In the old days this could usually be observed by seeing flashes of stainless where no laundry had settled on a section of the drum, the sound of the motor changing up and down in tone, and the drum swaying from side to side during the few minutes prior to spin which ran at “distribution” speed. All these signs meant the imminent spin was likely to be out of balance.

Forbes Rentals

Forbes specialise in renting Bosch appliances so they know them inside out. They also rent other brands and many other products – more details


What’s wrong with modern out of balance protection?

It’s an essential system, but they can sometimes be a bit too sensitive, with no override option. Allowing a customer to override the protection might be useful, I’m sure there are loads that refuse to spin that would actually be OK. However, I wouldn’t blame any manufacturer from shying away from giving customers the power to override their out of balance protection.

The answer is to make them more sophisticated and better at recognising when a load might be unbalanced but not going to cause a violent spin.

This sophistication costs money. Many washing machines may well have already got this protection just about right, but no one has compared these systems so far.


The more expensive washing machines such as Miele should have a more sophisticated system combined with higher quality suspension, which would cope better with unbalanced loads. It’s likely to be less paranoid about unbalanced spins but clearly still needs protection.

Conversely, cheap budget brands of washing machine are likely to have less sophisticated out of balance systems and be more fearful of letting a bad load spin because they know their crude suspension may not cope well with it.

I would expect that mid priced machines would have decent systems that may be less sensitive than budget machines but ultimately they all potentially suffer from the same side effect of refusing to spin some small or single item loads. There is likely to be some variance in tolerance and sensitivity between different makes but there’s no chart available that I’m aware of highlighting any differences.


For most people the advantages of protection from seriously damaging out of balance loads should far outweigh the inconvenience of the odd load not spinning.

Beware of large capacity washing machines

If you have a larger than normal drum such as 7 or 8 kg this problem may be worse because it takes more washing to make the drum nice and balanced than a smaller drum size.

Don’t buy a washing machine with a large drum if you do lots of small loads and don’t intend to double up your washing by washing large loads to save on the amount of washes you do.

Here’s a quote from the article linked to above –

… For example, my 7Kg washing machine will not spin 3 large towels. Last week my wife was extremely frustrated with our 7Kg drum washing machine as she had just washed our son’s hoody-top and wanted to spin it in the washer. It simply would not spin, so I advised her that it needed something to balance it out. She put in a couple of towels but still no spin..


…Eventually 5 towels were needed to balance out the absorbent top and allow a spin. This is a minor inconvenience compared to the benefit of being able to fit more washing in (even our king sized quilt) but it highlights how if you have a very large drum it could be more prone to not spinning small loads.

Washing machine won’t spin at all?

This topic is about washing machines not spinning small items or very small loads. Or occasionally not spinning the odd load but otherwise working OK. If your washing machine just will not spin at all then it is likely to have developed a fault unrelated to this topic. See related articles here –

Repairs
Fixed-price repairs, Pay monthly, Repair & protect your whole appliance..
Spares

Ransom Spares is a family company with over 1 million spare parts. Next day delivery available, friendly company with over 5000 reviews on Trust Pilot - Buy your appliance spare part

Price match promise: "If you find the exact same part cheaper, we’ll not only match it, we’ll beat it!"

Join Which?

Subscribe to Which? today and save 50% on our annual subscription for your first year. Offer ends 31 August. This offer is only available for new Which? annual subscriptions (excluding Gardening, Travel, Computing or Money packages)

79 thoughts on “Washing machine won’t spin just one item or very small load”

  1. Thank you so much for this type of service! I have this problem with my fairly new (<4years) Siemens and thought it was a fault. Many a time I have been close to taking a sledge hammer to the thing in frustration!! I have discovered through trial and error that setting it to a slower spin speed helps, but I will also try your tip of chucking a few more items into the spin cycle.

  2. Thanks Trish. The chances are it’s less sensitive on slower speeds as there’s less risk involved. Some will refuse to spin at all without a nicely balanced load but others will spin only on slower speeds.

  3. Hi,

    I would need your advise on this:
    If i wash salon towel by seprating them into a few laundry nets in a washer(big one)44kg. will there be any inbalance problems? or any damage caused to the washer?

  4. Thanks so much for that. It describes exactly the problem I’m having with a new 9kg Daewoo washer dryer. Will try again tomorrow with extra towels!

  5. I found this page while searching for the reason my 8kg WMD942 was leaving my washing very wet. It has been very useful reading all this as I was clueless about it. I just wanted to spin something (a wet pillow) and after waiting fifteen minutes for it to do its thing it still came out wet. I used to use an old hotpoint twin tub and you would put that rubber mesh thing on top, shut the lid and away it would go. You could tell straightaway if it was unbalanced and just lift the lid and sort it out. These modern conveniences have become so sophisticated they should be called INconveniences. I am about to try incorporating a bag of plastic bags to balance the pillow to see what it makes of that.

  6. I also have a Siemens WM145383 which is now 4 years old and am fed up with it and its out of balance problem. I have spent hours trawling through review websites looking for a replacement which has a solution to this out of balance problem. Thanks to your website I won’t be wasting my money buying a replacement…
    There’s money to be made here for washing machine manufacturers if they stop being so condescending to customers telling them its their fault not loading their machines properly. My previous old machine was fabulous and would wash anything I put in it and never caused any damage leaping about. I agree with previous postings-give us an override button (it can always give us a warning and disclaimer message for the necessary legal reasons) for pillows/bath mats/towel robes/wool cardigans/my son’s filthy rugby kit all of which cause me a headache when I try to wash them….I’m too busy to have to try and repeatedly spin these items ending up handwringing them. Maybe I should buy a mangle too!

Comments are closed.

Comments Policy

Comments welcome (unless closed). Comments need to be on topic with the article (Moderated before appearing).


Scroll to Top