Indesit washing machine flashing 3 times
F03 / error 3 means the NTC thermistor (temperature sensor) has a fault or its wiring connections are faulty. Before replacing the NTC, check that all connections to the thermistor and the PCB are clean and secure. Test the NTC thermistor with a multimeter before ordering a replacement – a thermistor is inexpensive, but confirming the fault is there before spending is always worthwhile.
Error code 3 or F03 on an Indesit washing machine indicates a fault with the NTC thermistor (temperature sensor) or its connections to the main PCB. The machine is detecting that water temperature cannot be correctly monitored or controlled. This fault is identical to Hotpoint error F03 – the full diagnostic guidance applies to both brands.
How to Identify This Error Code
On Indesit machines that use a flashing light display rather than a digital readout, error 3 / F03 is shown as the On/Off indicator light flashing 3 times, pausing briefly, then flashing a further 3 times – repeating continuously. On machines with a digital display, F03 will appear directly on screen.
What the NTC Thermistor Is
The NTC (Negative Temperature Coefficient) thermistor is the temperature sensor in the washing machine. It monitors the water temperature during the wash cycle and reports it back to the main PCB. The PCB uses this reading to control the heating element – switching it on and off to reach and maintain the selected wash temperature.
If the thermistor fails, reads incorrectly, or loses its connection to the PCB, the machine cannot confirm that water is reaching the correct temperature. Depending on how the fault manifests, the machine may abort the programme and display F03 rather than risk running a cycle at the wrong temperature.
Diagnosis and What to Check
-
Check the thermistor wiring connections.
The NTC thermistor sits on the heating element assembly at the base of the outer tub. It has two wires running from it to the PCB. With the machine unplugged, inspect the connector at the thermistor end and trace the wires back to the PCB connector. Disconnect and reconnect both ends to ensure a clean contact. A poor or corroded connection is a common cause of this error and is free to fix.
-
Test the thermistor with a multimeter.
An NTC thermistor changes its resistance with temperature. At room temperature (approximately 20 degrees) a typical washing machine NTC should read around 6,000 to 10,000 ohms. In very hot water its resistance drops significantly. A reading of zero (short circuit) or infinite resistance (open circuit) confirms the thermistor has failed. See our full guide on how to test an NTC thermistor for the step-by-step process.
-
Replace the NTC thermistor if confirmed faulty.
NTC thermistors are relatively inexpensive and straightforward to replace. Ensure the replacement is the correct type for the specific model. NTC sensors and thermostats for Indesit and Hotpoint washing machines are available at Spares4Appliances.
-
If the error persists after replacing the NTC – consider the PCB.
If a confirmed working NTC is in place and the error continues, the fault may be in the PCB itself. PCB replacement is expensive and should only be considered after the thermistor and all wiring connections have been verified. An engineer with diagnostic equipment is recommended at this stage.
Indesit and Hotpoint washing machines share many components and control systems. Error F03 has the same meaning on both brands. See our guide on Hotpoint error code F03 for additional diagnostic context.
Need Parts or a Repair?
Related Guides
How to Test an NTC ThermistorStep-by-step guide to testing the NTC thermistor with a multimeter to confirm whether it has failed.
Hotpoint Error Code F03The same NTC fault on Hotpoint machines – identical diagnosis and repair applies to Indesit F03.
Washing Machine Not Heating WaterFull guide to heating faults including heater element, NTC, and PCB diagnosis.
Indesit Error Code F07Another Indesit heating system error – motor triac fault diagnosis.
Frequently Asked Questions
What does error code F03 mean on an Indesit washing machine?
F03 (also displayed as 3 flashes on machines without a digital display) means an NTC thermistor fault. The NTC is the temperature sensor that monitors water temperature during the wash cycle. The error indicates the machine cannot correctly read the water temperature – either because the thermistor has failed, its connections are faulty, or in rarer cases, the PCB has a fault.
Can I fix Indesit F03 myself?
Checking and reseating the wiring connections to the thermistor is a straightforward check that requires only unplugging the machine and locating the thermistor connector. Testing the thermistor with a multimeter and replacing it if confirmed faulty is also within reach for a confident DIY repairer. If the fault persists after replacing the thermistor, an engineer is recommended as the fault may be in the PCB.
Is Indesit F03 the same as Hotpoint F03?
Yes. Indesit and Hotpoint washing machines share the same underlying control systems and components through their common ownership under the Whirlpool group. Error F03 has the same meaning and the same diagnostic process on both brands.
Indesit or Hotpoint error code F07 or light flashing 7 times
F07 means the heater relay on the PCB has a fault – usually a jammed relay. The heating element is controlled via a relay built into the main PCB. When this relay sticks, the machine detects the fault and displays error 7. PCB replacement is the typical fix, but because the PCB also requires the EEPROM memory chip to be transferred and reprogrammed, this is an engineer-only repair.
Error 7 or F07 on Indesit (and some Hotpoint WF/WD) washing machines indicates a heater relay fault. The relay that switches the heating element on and off is embedded in the main PCB and is known to jam on these models. This fault almost always requires PCB replacement by a qualified engineer – it is not suitable as a DIY repair.
How This Error Code Is Displayed
On Indesit and compatible Hotpoint machines with a digital display, the error appears as F07. On models with a rotary control dial but no digital display, the door lock indicator light flashes in repeating cycles of 7 flashes. This applies to certain Hotpoint WF and WD models as well as Indesit machines – both brands share the same platform and control systems through their common ownership under the Whirlpool group.
What F07 Means – The Heater Relay
The heating element in a washing machine does not connect directly to the mains supply – it is switched on and off via an electromechanical relay on the main PCB. This relay receives a signal from the PCB’s processor to switch the element on, and another signal to switch it off. When the relay jams in the closed (on) position, the PCB detects that it cannot control the heater correctly and reports error 7.
Unlike some components that can be replaced individually, the heater relay is soldered into the main PCB. It cannot be replaced in isolation without specialist electronics equipment. If the relay has failed, the entire PCB requires replacement. There are anecdotal reports of engineers temporarily freeing a jammed relay with a firm tap to the PCB – but a relay that has jammed once is likely to jam again, making this only a temporary fix at best.
Why This Is an Engineer-Only Repair
Why DIY PCB replacement is not recommended
- A new PCB does not come with the EEPROM memory chip pre-fitted. The EEPROM stores the machine’s programme data and must be either transferred from the old PCB or programmed specifically for the machine. This requires specialist equipment and knowledge
- PCBs are expensive components – typically £80 to £200 or more – and are non-returnable once fitted. If the fault is not cured by the PCB replacement (which can happen if a connection fault was the cause), the cost is lost
- If the fault persists after fitting a new PCB, there is no route to return the part and recover the cost
- An engineer can verify the fault more precisely before ordering parts, reducing the risk of an unnecessary replacement
Washing machines contain capacitors that can retain an electrical charge even after the machine has been unplugged. This charge can deliver a painful and potentially dangerous shock. Any internal investigation of the PCB or other components must only be carried out by someone with appropriate electrical knowledge and after allowing time for capacitors to discharge. See our guide on electric shock risk from appliances when unplugged.
What to Do
-
Check whether the machine is still under guarantee. Indesit and Hotpoint machines often come with a 5-year parts warranty. If the machine is within this period, contact the manufacturer to arrange a repair under the parts warranty. The labour charge may still apply but the PCB and EEPROM parts costs should be covered. -
Get a quote for engineer repair before deciding. PCB replacement on an older machine can be uneconomical compared to replacement. An engineer can assess whether the repair is worthwhile given the machine’s age and condition before parts are ordered. -
Consider a fixed-price repair scheme. Some manufacturers and independent repair companies offer fixed-price repairs covering parts and labour. This can make an otherwise expensive PCB repair more predictable in cost.
Book a Repair
Related Guides
Indesit Error Code F03NTC thermistor fault on Indesit washing machines – diagnosis and when to call an engineer.
Indesit Error Code F04Pressure system fault on Indesit machines – what the code means and what to check.
Washing Machine Not Heating WaterFull guide to heating faults including relay, element, NTC, and PCB diagnosis.
Washing Machine Lights FlashingHow to read flashing light error codes on machines without a digital display.
Frequently Asked Questions
What does Indesit error code F07 mean?
F07 indicates a heater relay fault. The relay that switches the heating element on and off is built into the main PCB. When it jams, the machine detects it cannot control the heater correctly and reports F07. On machines without a digital display, this appears as 7 flashes of the door lock indicator light in a repeating cycle.
Can I fix Indesit F07 myself?
PCB replacement – which is the typical fix for F07 – is not recommended as a DIY repair. The new PCB requires the EEPROM memory chip to be transferred or reprogrammed, which needs specialist equipment. PCBs are expensive and non-returnable once fitted. If the fault is not cured, the cost cannot be recovered. An engineer who can verify the fault before ordering parts is the appropriate route.
Is Indesit F07 the same as Hotpoint F07?
Yes. Indesit and Hotpoint machines share the same control systems and PCB architecture. Error F07 has the same meaning on Hotpoint WF and WD models. Both brands are manufactured under the Whirlpool group and the fault diagnosis and repair process is identical across both.
How to cancel the error code on an AEG washing machine
On most washing machines, error codes clear automatically once the underlying fault is repaired – no manual reset is needed. However, some AEG Lavamat models retain the error code in memory even after the fault has been fixed, requiring a manual reset procedure. Simply cancelling the code without fixing the fault will cause it to return immediately.
Do AEG Error Codes Need Resetting?
On most washing machines, an error code is generated by the control system when a fault is detected during the wash cycle. Once the fault is repaired, the code clears on the next run. No manual reset procedure is required.
Some older AEG Lavamat models behave differently – they store the last error code in memory and continue to display it even after the fault has been repaired. This requires a manual reset to clear. This only presents a practical issue when a repair has been carried out without an engineer – a professional engineer would carry out the reset as part of the repair process.
Resetting an error code without repairing the underlying fault will not resolve the problem. The code will return as soon as the machine detects the fault condition again. Always identify and repair the cause before attempting a reset. If the fault has not been diagnosed, see our guide on washing machine error codes and flashing lights.
How to Reset the Error Code on an AEG Lavamat
The following procedure runs a short test cycle that clears stored error codes on some older AEG Lavamat models. The exact button combination varies between models – two confirmed variants are described below.
-
Turn the rotary programme knob to the off position.
The machine must be switched off at the programme dial before beginning the reset sequence.
-
Hold in the Pre-wash and Soak button simultaneously.
Keep both buttons held down while completing the next step.
-
Turn the rotary knob to the Gentle (or Short) Spin position.
This is the most commonly reported position for initiating the test sequence. On some models, turning the knob clockwise to the Energy Saving position instead produces the same result. If one position does not trigger the test cycle, try the other.
-
Allow the short test sequence to run.
The machine should run a brief diagnostic cycle. Once complete, the stored error code should be cleared.
This reset method has been confirmed on specific older Lavamat models. It may not apply to all AEG washing machines or to current production models. If the procedure does not produce a response from the machine, consult the instruction manual or contact AEG directly for the correct reset method for the specific model. The model number is on a sticker inside the door frame.
Need a Repair?
Related Guides
Washing Machine Lights FlashingHow to read flashing light error codes on machines without a digital display.
AEG Error Code E35What AEG error code E35 means and how to diagnose the fault.
Programme Dial Keeps TurningWhy the rotary dial clicks through programmes continuously – and what error conditions cause this.
Indesit Error Code F07Heater relay fault on Indesit and Hotpoint machines – why this requires an engineer rather than a reset.
Frequently Asked Questions
Do I need to reset an AEG washing machine error code after a repair?
On most washing machines, error codes clear automatically once the fault is repaired. Some older AEG Lavamat models store the last error code in memory and require a manual reset even after the fault has been fixed. If an error code persists after a confirmed repair, the test cycle reset procedure described above may clear it.
Will resetting the error code fix the problem?
No. Resetting clears the stored code from the machine’s memory but does not repair the underlying fault. If the fault condition still exists, the code will return as soon as the machine detects it again during the next cycle. The fault must be identified and repaired first.
What if the reset procedure does not work on my AEG?
The procedure described is specific to older AEG Lavamat models and may not apply to all machines. If it does not produce a response, check the instruction manual for the specific model or contact AEG customer services. Alternatively, an engineer attending the machine can carry out the reset alongside the repair.
Indesit washing machine light flashes 7 times
Indesit machines with a rotary dial rather than a digital display indicate fault codes through the door lock LED, which flashes in repeating cycles. 7 flashes means heater relay stuck on the PCB. This is confirmed as error code F07 on models with a digital display. The rotating dial clicking continuously is the machine’s way of showing it is in an error state. See also our full guide on Indesit error code F07.
On Indesit washing machines with a rotary control dial, 7 flashes of the door lock indicator light is the equivalent of error code F07. This indicates a heater relay fault on the main PCB. The repair almost always requires PCB and EEPROM chip replacement by a qualified engineer – it is not recommended as a DIY repair.
How Indesit Dial Machines Display Error Codes
Many budget Indesit washing machines use a rotary programme selector dial rather than a digital display panel. When a fault is detected, these machines cannot show a code on a screen. Instead, they communicate the fault in two ways simultaneously:
The rotary dial keeps turning and clicking
The programme selector dial rotates continuously through its positions, clicking as it goes. The machine is not actually cycling through programmes – this is the control system stuck in an error loop. See our guide on programme dial clicking continuously.
The door lock light flashes in a repeating pattern
The door lock indicator LED flashes a set number of times, pauses, then repeats. Count the flashes per cycle to identify the error code. 7 flashes corresponds to error code F07 – the same code shown as “F07” on machines with a digital display.
What 7 Flashes Means
Seven flashes of the door lock light on a rotary-dial Indesit washing machine indicates a heater relay fault. The relay that switches the heating element on and off is embedded in the main PCB. When it jams, the control system detects it cannot switch the element correctly and reports this as error 7.
A connection fault on the heater, or an open circuit (failed) heating element, can cause a different symptom: the machine goes completely dead and refuses to respond – with the exception that the indicator LEDs still light up. This is a different presentation from the 7-flash error. The same dead-machine symptom can also be caused by an open circuit motor or other component failures, so the flashing light count remains important for accurate diagnosis.
Why This Is Not a DIY Repair
Why PCB replacement should not be attempted as DIY
- The heater relay is soldered into the PCB – it cannot be replaced in isolation. The entire PCB must be replaced
- A new PCB does not include the EEPROM memory chip, which must be transferred from the original board or separately programmed. This requires specialist equipment
- PCBs are expensive and non-returnable once fitted. If the fault is not resolved, the cost is lost
- An engineer can verify the exact fault before ordering parts, reducing the risk of an unnecessary PCB replacement
Washing machines contain capacitors that can retain a charge after being unplugged. Do not investigate internal components without appropriate electrical knowledge and after allowing time for capacitors to discharge. See our guide on shock risk from appliances when unplugged.
Need a Repair?
Related Guides
Indesit Error Code F07Full guide to the F07 heater relay fault – diagnosis, PCB replacement, and engineer options.
Programme Dial Keeps TurningWhy the rotary dial clicks continuously – and how to read the door light flash count alongside it.
Washing Machine Lights FlashingGeneral guide to reading flashing light error codes across different brands and models.
Washing Machine Not HeatingFull diagnosis of heating faults – element, relay, NTC, and PCB causes.
Frequently Asked Questions
What does 7 flashes on an Indesit washing machine mean?
On Indesit washing machines with a rotary control dial, 7 flashes of the door lock indicator light indicates a heater relay fault – the same as error code F07 on machines with a digital display. The relay that switches the heating element is embedded in the main PCB and has developed a fault. PCB replacement is typically required.
Why is the dial on my Indesit washing machine turning and clicking continuously?
A continuously rotating and clicking programme dial means the machine has detected a fault and is stuck in an error state. Count the number of times the door lock light flashes between pauses to identify the error code. The number of flashes corresponds to the F0X error code – 7 flashes means F07, 3 flashes means F03, and so on.
My Indesit has gone completely dead but the lights come on – is this related?
A completely dead machine that still shows indicator lights is a different symptom from the 7-flash error, though both can involve the heater circuit. A connection fault or open circuit on the heating element, or an open circuit motor, can cause the machine to appear dead. This requires an engineer to test individual components rather than relying on the flash count alone.
Hoover error code E1
Watch the cycle carefully and note exactly when it aborts. Early in the cycle during filling – investigate a fill fault. During the wash once filled – investigate a heating fault. Just before or during spin when draining should be occurring – investigate a drain fault or pressure system fault.
Error E1 on older Hoover New Wave washing machines is a shared error code that covers three entirely separate fault types: a timeout on filling with water, a timeout on heating the water, and a timeout on draining. The position in the cycle where the machine aborts is the key to identifying which of the three faults is responsible.
How to Identify Which Fault Is Causing E1
Because E1 covers three different fault types, the first diagnostic step is to watch the cycle run until it aborts and note precisely when and where in the programme E1 appears.
| When E1 appears | Likely fault type | Where to investigate |
|---|---|---|
| At the very start of the cycle, or during filling for rinses | Fill timeout | Water supply, inlet tap, fill hose, inlet valve, water pressure |
| During the wash stage after successfully filling, typically 15 to 20 minutes in | Heat timeout | Heating element, element connections, NTC thermistor, PCB |
| Just after the wash finishes when the machine should be pumping out, or during rinsing when it has filled but should be draining | Drain timeout | Pump filter, pump, drain hose, pressure system |
| Just before spin, after water appears to have drained | Pressure system fault | Pressure chamber, pressure hose, pressure switch |
E1 During Filling – Fill Fault
If the machine aborts with E1 at the start of the cycle or when trying to fill for rinsing, the water is not reaching the required level within the allowed time. Common causes:
-
Check the supply tap is fully open. A tap that appears open but is partially seized, corroded, or cracked internally can severely restrict flow. Turn it fully and check whether the issue changes. -
Check the fill hose for kinks or blockages. A kinked hose restricts flow. Also check the mesh filter inside the inlet valve connection for limescale or debris – turn off the tap, disconnect the hose, and inspect the filter screen. -
Check water pressure is adequate. Low mains pressure can cause fill timeouts even when everything is correctly connected. See our full guide on washing machine fill faults.
E1 During the Wash – Heat Timeout
If the machine fills successfully, begins washing, then aborts with E1 approximately 15 to 20 minutes into the wash cycle, the heater is not bringing the water to the required temperature within the allowed time. This is a heating fault, not a fill or drain fault.
-
Check for a faulty or open circuit heating element. An element that has failed or has a broken connection will not heat the water at all. The machine waits the full heat timeout before aborting. -
Check the element connections. A loose or corroded connection on the element terminals can prevent the element receiving power even if the element itself is functional. -
Check the NTC thermistor. The NTC thermistor monitors water temperature. A failed thermistor can cause the PCB to read the temperature incorrectly, either aborting prematurely or continuing to heat indefinitely. See our guide on washing machine not heating water.
E1 During Draining – Drain Timeout or Pressure System Fault
If the machine aborts with E1 at the point where it should be pumping water out – whether before rinsing, during rinsing, or just before spin – the fault is in the drain system or the pressure system that detects whether the water has been removed.
-
Check and clean the pump filter. A blocked filter prevents the pump from draining effectively. Locate the filter at the front base of the machine, drain residual water, and remove any debris. See our guide on washing machine pump filters. -
Listen for the pump running. If the pump can be heard running during the drain stage but water is not clearing, suspect a blockage between the pump and the drain outlet. If the pump is not running at all, suspect a jammed pump impeller or pump motor fault. -
If water appears to drain but E1 still shows just before spin – check the pressure system. The machine uses a pressure switch and chamber to confirm all water has been removed before allowing spin. If the pressure chamber, the thin pressure hose connecting it, or the pressure switch itself is faulty, the “water gone” signal is never sent. The machine correctly drains the water but cannot confirm this, so it aborts. Check the pressure hose for blockages (a blocked chamber hose is a known Hoover fault on older models) and the pressure switch for continuity.
Need a Repair?
Related Guides
Washing Machine Won’t Fill With WaterFill fault diagnosis – taps, hoses, inlet valves, and water pressure causes.
Washing Machine Not Heating WaterHeating fault diagnosis – element, NTC thermistor, connections, and PCB.
Washing Machine Won’t DrainDrain fault diagnosis – pump, filter, blockages, and electrical causes.
Hoover Nextra Lights FlashingError codes on Hoover Nextra washing machines – a different model range from the New Wave.
Frequently Asked Questions
What does E1 mean on a Hoover New Wave washing machine?
E1 is a timeout error that covers three different fault types: a timeout on filling with water, a timeout on heating the water, and a timeout on draining. The point in the cycle where the machine aborts identifies which fault type is responsible. Early in the cycle – fill fault. During the wash after filling – heat fault. Before or during spin when draining – drain or pressure system fault.
My Hoover shows E1 just before spin but the water seems to have drained – why?
The machine confirms all water has been removed using a pressure switch and pressure chamber rather than by directly sensing water. If the pressure chamber or its connecting hose is blocked, or if the pressure switch has failed, the machine cannot receive the “water gone” confirmation even though the drum is empty. It therefore refuses to spin and displays E1. Check the thin pressure hose for blockages – a clogged pressure chamber hose is a known issue on some older Hoover washing machines.
How do I know if the E1 is a heat fault or a drain fault on my Hoover?
Watch the cycle carefully. A heat timeout occurs during the wash stage – the machine fills successfully, begins washing, and then aborts approximately 15 to 20 minutes later while the wash is still running. A drain timeout occurs after the wash has completed, when the machine should be pumping water out. If the machine aborts while the drum is still full of soapy wash water – heat fault. If it aborts when trying to drain – drain fault.
LG washing machine error code OE
Check whether water is still inside the drum when OE appears. If the drum is full or partially full of water – a physical drain fault is the cause, start with the pump filter. If the drum appears empty but OE still shows – a pressure system fault may be preventing the machine receiving the “water gone” signal.
Error code OE on an LG washing machine means the machine has detected that water is not draining correctly within the expected time. The most common causes are a blocked pump filter or a blockage inside the pump impeller. OE can also be triggered by a faulty pump motor, a blocked drain hose, or a pressure system fault that prevents the machine detecting that the water has gone.
What OE Means on an LG Washing Machine
OE stands for an outflow (drain) error. The machine monitors the drainage process and expects the water level to drop within a set time. If that drop is not detected, OE is displayed and the cycle aborts. The code does not identify the specific cause – it indicates the machine cannot confirm the water has gone.
Diagnosing OE: Two Scenarios
Water still in the drum when OE appears
The machine is trying to drain but the water is not clearing. This is a physical drain fault – blockage in the filter, blockage or jam in the pump impeller, a blocked drain hose, or pump motor failure. Work through the drain fault diagnosis below.
The water has drained but the machine still cannot confirm this and refuses to proceed to spin. This is a pressure system fault – the sensor that tells the machine the drum is empty is not receiving or sending the correct signal. This is a more involved diagnosis – see our guide on pressure system faults.
Checking for a Drain Blockage
-
Check and clean the pump filter.
The pump filter on most LG front-loading washing machines is accessible behind a small panel at the front base of the machine. Place towels on the floor, slowly unscrew the filter cap to release residual water, then remove and clean the filter. Check for coins, hairbands, hair grips, small socks, and accumulated lint. See our guide on washing machine pump filters.
-
Listen for the pump running.
When the machine attempts to drain, can the pump be heard? A running pump with no drainage suggests a blockage downstream of the pump – in the drain hose or at the standpipe connection. A silent pump suggests the pump motor is not running – either a jammed impeller or a failed motor.
-
Check the pump impeller through the filter opening.
With the filter removed, shine a torch into the pump chamber where the impeller is visible. Objects such as glass fragments, coins, or small items can jam the impeller. The impeller should turn freely by hand. If it will not rotate or is broken, the pump needs replacement.
-
Check the drain hose connection.
Confirm the drain hose is not kinked, and that the standpipe or U-bend connection is not blocked. A small object or accumulation of lint at the standpipe connection can restrict flow enough to cause OE. This check does not require moving the machine if the drain hose exits at the back and runs to a standpipe under the sink – unscrew the spigot and check inside.
-
If no blockage is found – consider an engineer.
If the pump is running, there is no blockage in the filter or drain hose, and the drum is still not emptying, see our guide on no blockage but still not draining. Pump motor failure and pressure system faults are the remaining causes.
LG documentation states that the machine must be level and that the front cannot be higher than the back or vice versa. Poor levelling can leave a small residual amount of water in the machine but is unlikely to prevent draining entirely. If OE appears and the machine is visibly unlevelled, correct the levelling first and test again before investigating further.
Related Guides
Related Guides
Washing Machine Won’t DrainFull drain fault diagnosis – pump, filter, blockages, and electrical causes.
Washing Machine Pump FilterWhere to find the pump filter and how to clean it – the first place to check for OE.
No Blockage But Still Not DrainingWhen the filter is clear but the machine still won’t drain – further diagnosis including pressure system checks.
Samsung Error Code 5EThe same drain timeout error on Samsung washing machines – similar causes and diagnosis.
Frequently Asked Questions
What does OE mean on an LG washing machine?
OE is a drain error – the machine has detected that water is not leaving the drum within the expected time. It most commonly indicates a blocked pump filter, a jam in the pump impeller, or a blocked drain hose. It can also be triggered by a pump motor fault or a pressure system fault that prevents the machine detecting the drum is empty.
My LG shows OE but the drum looks empty – what does this mean?
If the water has drained but OE still displays and the machine will not spin, the pressure system is likely at fault. The machine uses a pressure switch to confirm the drum is empty before spinning. If this system is not providing the correct signal – due to a blocked pressure chamber hose, a faulty pressure switch, or a PCB issue – the machine will not proceed to spin even though the drum is actually empty. This requires a more detailed diagnosis, ideally by an engineer.
How do I reset the OE error on an LG washing machine?
Clearing the error code without resolving the underlying fault will cause OE to return immediately on the next cycle. The fault must be identified and resolved first. Once the drain fault is fixed – whether by cleaning the filter, clearing a blockage, or repairing a component – the error should clear on the next successful drain.