I have a previous article describing exactly how a washing machine controls water levels. This article is a follow up to it describing some of the faults that can occur with the pressure system on a washing machine or Washer dryer.
What is the pressure system?
The pressure system is made up of several parts. It has a simple purpose and that is to tell the washing machine when water inside the drum has reached a specific level, and when all the water has been successfully pumped away. If something goes wrong and the washing machine does not receive these signals then the washing machine can either overfill, or refuse to spin.
Various things can go wrong causing symptoms described below – but all these symptoms have other possible causes too. So it’s important not to make assumptions. In order to try and understand pressure system faults you should read the first article to understand how the pressure system works.
They are normally very reliable, but it’s possible for a pressure switch to be faulty.
The pressure switch
However, in my experience it is the last thing to suspect. Never fit a new one if you haven’t ruled out all other faults – especially a blockage in the pressure chamber bottle at the base of the outer drum (details later). A switch sticking on will make the washer think there’s water inside the drum when there isn’t. Conversely, sticking in the off position will tell the washer there isn’t any water in when there is.
The former would cause the washing machine to not do the fast spin. The latter would cause it to overfill. However, neither of these symptoms are exclusively related to a stuck pressure switch – there are more likely causes. Remember, a pressure switch is far more likely to be stuck because of a blockage.
Forbes rent appliances and specialise in renting Bosch appliances so they know them inside out. They also rent other brands and many other products – more details at Forbes
The modern pressure switch
The pressure switches shown and described above have now been replaced with a different type. Instead of having mechanical switches inside that are operated by air pressure they have small coils with magnets inside that give a different resistance reading depending on how much air pressure is applied.
The old style pressure switch has remained virtually unchanged for 40 years or more and has usually been one of the more reliable parts on a washing machine. It remains to be seen whether these (obviously cheaper) designs are reliable or not but in theory they ought to be very reliable still (if not more so) because of the reduced number of parts. Troubleshooting these modern pressure switches may be a bit more difficult without knowing the expected resistance readings.
The small pressure switch tubing between the pressure switch and pressure chamber bottle
Damage to the pipe, or air leaks at the connection points on the pressure switch or plastic pressure chamber bottle can cause overfilling because air pressure is lost. Without an airtight connection it’s impossible to create enough pressure to activate the pressure switch or at last to keep it switched on..
Pressure chamber bottle
If the pressure chamber at the bottom of the tube gets blocked with gunge inside, then when the washing machine empties the water, the water inside the pressure chamber (which is only really a small plastic bottle) gets trapped because it can’t get past the gunge. This means that the air pressure is held inside the plastic tube so the pressure switch is jammed ON.
A blocked pressure chamber bottle can also restrict or prevent water getting into the bottle in the first place causing the washer to take in too much water or to overfill.
This would need a fairly solid blockage though and is much more rare than trapping the air pressure as described in the last paragraph. This is because the sheer volume of water inside the tub can sometimes force its way past gunge into the bottle, but because hardly any water actually goes into the bottle this very small amount cannot force its way back out when it drains (if there is a blockage).
If a pneumatic door lock is fitted that prevents the door opening when full of water, a part of the small pressure tubing (at the top of the pressure chamber bottle) branches off and fits onto the door lock. The air pressure is therefore also used to operate a lock inside the door as described in this article different types of door locks.
This type of interlock is rarely used these days because of cost cutting, but it used to be common on washing machines from the 90s. The relevance here is that gunge inside the pressure chamber bottle can also trap air in the tube that leads to the door lock preventing it from opening even when water has been pumped away.
Fixing a blocked pressure system
This article looks specifically at blocked pressure systems and how to fix or diagnose one how to clear a blocked pressure system
Other symptoms
Not taking any water in or refusing to do a fast spin are other possible symptoms of faults on the pressure system related to the machine thinking there is water inside when there isn’t – but as with most of the other symptoms, other unrelated faults can cause the exact same symptoms. General help for these two faults can be found here – not taking in water and not spinning.
Finally, a fault in the pressure system can cause the washer to abort the programme and give an error code – appliance Error codes – What You Need to Know
Get an engineer
Faults on the pressure system can be difficult to diagnose. They can also be very easily misdiagnosed when a fault is caused by something totally different. Don’t just start messing with or replacing parts in the pressure system because your washing machine exhibits symptoms that can be caused by the pressure system. Unless you fully understand how it all works you will be better advised to call an engineer.
Repairs
Fixed-price repairs, Pay monthly options, Repair & protect your whole appliance..
Save Money Now
Subscribe to Which? today and start saving money now. Subscription offers often available.
Spares
Spares4Appliances is a spares company run by repair engineers who understand all about spare parts for appliances.
Zanussi ZWG6122 failed to complete cycle – pump filter blocked. Easy enough to clear this, but then the machine wouldn’t do anything other than drain – all other programmes just turned on the pump, as though the machine was already full of water. Disconnected tubing from pressure switch and blew down it. Initially blocked but blew harder till bubbling noise from pressure bottle. Blockage cleared, pressure switch functions again and machine now fully operational.
Many thanks for your article – saved me over £200.
hi there,
I have an indesit which on any cycle will start filling the drum for approx 5 seconds (if I open the fabric softener door I can see that water is traveling past and at a normal flow) then stops and hangs.
I’ve taken the filter system completely apart, should I approach the pressure system next you reckon?
Thank you very much
Hello Billy. If it is a hot and cold fill washing machine there could be a problem with the hot water supply or the hot water valve in the machine. A washing machine will normally fill up with cold water for several seconds, pause, and then start taking hot water. If it is cold fill only with just one water valve then it is going to be difficult fault to deal with because clearly everything is working all right to allow it to start taking water in at all.
A pressure system fault could cause issues with water levels but if the pressure system erroneously thinks the water has gone into the machine okay and stops the fill process it should then proceed to wash. So if the washing machine is hanging this implies that it is still waiting for the pressure system to be activated. Therefore suspect is more likely to be a problem in getting the water into the machine.
If there are more than one fill valve check this article for troubleshooting a water valve not taking in water
Hi there. I’m trying to resolve a problem with my front loading LG machine (F1480QDS). The machine has been temperamental for a couple of weeks, regularly stopping towards the end of a cycle with the OE code. Even when the machine does – rarely – complete a cycle, there is often some water left, albeit it’s generally below the level of the drum. It does seem to drain some but not all of the water – I got a shock the first time I took the filter out when a significant amount of water came out. Interestingly this wouldn’t drain out of the drain hose. I’ve also noticed it’s not been washing properly, and doesn’t appear to be rinsing effectively. I originally thought it was a blocked filter and/or blocked drain hose but have managed to discount both of those now. I took the pump out of the machine yesterday to see if there were any other noticeable blockages/faults but none seen. I’ve ordered a replacement pump thinking it can only be the pump, but your article has now got me thinking about other potential causes. Any advice gratefully received.
Further to my request above, I’m please to say I’ve resolved the fault – new pump fitted = problem fixed. Most satisfying, and only ~£20 for new pump from eBay.
my candy 1682d front loader washing machine is not spinning and show error 03, i try blowing air through the pressure switch hose then it spin and washing operation completed.it fault came up again after some days then i repeat the same operation but it did not work so i tried the reset procedure it then worked. After some days of washing the same error code came up again.i have tried all i know but still it wont spin.i need your asistance
It could be that there is a blockage in your pressure bottle that is only temporarily cleared when you blow down it. The relevant advice is in my article under the section, “Pressure chamber bottle”. There is a link under that section that goes to a full article about clearing a blocked pressure system. It’s best to call an engineer if reading this article doesn’t help.
Hi, I have a hoover OPH 714D washing machine, when i switch the machine on everything seems normal but when i choose a program the drain pump starts working and the door locks but no water is in the machine. I tried opening the door of the machine emptied a bucket of clean water maybe something else happenes but the water was emptied and the drain pump continued on working. I am to check the pressure switch by blowing and maybe trying to hear some clicking noises, i will then go to the pressure chamber which maybe there is any blockage.
Any pointers please maybe you had a similar problem.
Hello JPG. A fault on the pressure system could cause the machine to think it already has water in and stop it from taking in water. However, if it thinks it already has water in it should start turning the drum and “washing”. Such faults can also cause the heating element to energise which is a very bad thing with no water inside.
So if it isn’t turning the drum back and forth it’s unlikely to be a pressure system fault. I would start at this article Washing machine won’t fill with water
However, if it starts a cycle by running the pump (which is normal) but then the pump doesn’t stop running it won’t be a fault with filling. This is because the pump should stop before it tries to take in water. If the pump doesn’t stop running it is stuck. A fault on the pressure system might be a cause but if so it shouldn’t work on the spin cycle either. Does it spin OK on a spin only cycle?
I had this same problem twice now and both times it turned out to be the heating element
Hi, your article was very informative but i need specific places where i need to check due to the continuous draining. You mentioned that “Various things can go wrong causing symptoms described below but all these symptoms have other possible causes too”, from your experience where do i need to start in sorting out the problem
Thanks Patrick. Which problem did you have that turned out to be the element?