Ice in base of freezer

Sheet of ice in base If water is freezing in the  base of a freezer this is a common problem. I’ve recently had to repair my own freezer with this problem and this article documents what I did to fix the fault. This issue can affect stand alone freezers, or the freezer section of a fridge-freezer.

Sometimes a build up of ice may also (or exclusively) be hidden behind the back wall of the freezer. This can cause the freezer to not cool down to the correct temperature due to restricted airflow, and/or cause a high pitched searing noise if the circulating fan catches on the encroaching ice. Eventually the ice can jam the fan completely causing a major loss of cooling.


A build up of ice in the base can be caused by a blockage in a channel designed to direct water into an evaporation tray. This causes water to spill over the channel and into the base of the freezer where it of course freezes. The fact that this water freezes tends to indicate that the freezer is otherwise functioning OK. The build up of ice can prevent the bottom drawer from opening properly causing it to get broken when frustratingly rammed shut or forced open.

Clear ice from the base

Defrosting the freezer is the easiest way to deal with this. However, this often only proves to be a temporary fix because most people don’t defrost it thoroughly enough. Defrosting until all the visible ice in the base has gone isn’t enough. The blockage is usually caused by solid ice in the drain hole behind the back wall, or there is ice packed behind the back wall. Because this wall is insulated a normal defrost will usually leave ice still in place. New water will continue to run into the base and freeze up again.


To properly defrost a freezer with this suspected fault you need to unplug it and leave the door open for 24 hours, or remove the back wall and let it defrost (optionally carefully assisting with a hair dryer).

Ice must be removed from behind the back panel

To make sure the ice was completely gone, and that the hole in the drain channel was clear, I unplugged the freezer and then took off the plastic cover at the back of the freezer inside.

In my case there were only 4 screws to remove. The cover came off easily revealing the fan and channel with all the excess ice (see photo below).

If the plastic wall is frozen up and won’t come cleanly off after the screws are removed – don’t force and break it. Allow it to defrost a while, or use a hair dryer to gently warm it up around the edges.

Get your appliance repaired

Choose from the following list of appliance repairers..

Fixed-price repairs, Pay monthly, Repair & protect..

Ice in back of freezer

The first photo at the top of this page shows the ice in the base of our freezer. The previous photo shows the ice that was behind the back cover. It’s in the bottom right corner under the metal section. You can also see the sloping channel where defrosted water should run down to the right and out through the drain hole in the corner. The hole was blocked solid with ice. You can even see the trickle line where water has run from the channel into the base.

Taking care not to get too close to any plastic or sensors I assisted the defrosting by carefully blowing warm air with a hair dryer* (see warning below). I also poured a little warm water into the hole to melt through the ice blocking it up. I then pushed a small bit of plastic through the hole to make sure it was clear. It was then just a matter of re-fitting the plastic back wall, plugging the freezer back in and using the fast freeze option to assist getting it back down to temperature as quickly as possible.

The photos below show the ice blockage before and then the clear drain channel and hole after proper defrosting.


Before

close up of ice blockage

After Defrosting

cleared drain hole


What causes the blockage?

Clearly ice should not build up at the back and block the drain hole. There could be a fault in the PCB or a sensor causing it to over-freeze. Or even (if fitted) a failure in the auto defrosting system. Excessive frosting which looks more like hard snow than clear ice can be caused by moist warm air getting drawn into the appliance as described in this article Icing up in fridge or freezer. If the fault quickly re-occurs you need to call an engineer.

Forbes specialise in renting Bosch appliances so they know them inside out. They also rent other brands and many other products.

  • No initial financial outlay
  • Prices start at around £3.91 per week
  • No more repair bills
  • Fast repair service same day/next day
  • No stress trying to find a repairer
  • Stop constantly having to buy new ones

Evaporation tray This photo show the main compressor at the back of the freezer. Above it is a black plastic tray. This is where water from the channel inside runs. The heat generated from the compressor slowly evaporates the water. If the channel inside the appliance is blocked as described in this article water will instead run into the base of the appliance.

* Warning

Regarding my freezer featured in this article, I eventually realised that the channel that the defrosted water ran down and into the hole had a bulge in the plastic just before the hole. When I first noticed a large sheet of ice in the base of the freezer I used a heat source to defrost it quickly. So it is possible that I “may” have warped the plastic inside the channel. This was unrepairable.

However, it’s possible that it was warped when I bought it due to a manufacturing fault. If you use a hairdryer (never anything more powerful) you should be very careful not to warp any plastic.

Affected by temperature of room?

How are fridges and freezers affected by room temperature? | Can you run a fridge or freezer in a garage?

Repairs
Fixed-price repairs, Pay monthly, Repair & protect your whole appliance..
Save money

Subscribe to Which? today and start saving time and money

Various membership options available.
Spares

Ransom Spares is a family company with over 1 million spare parts. Next day delivery available, friendly company with over 5000 reviews on Trust Pilot - Buy your appliance spare part

Price match promise: "If you find the exact same part cheaper, we’ll not only match it, we’ll beat it!"

Comments need to be on topic with the article (Moderated before appearing).

26 thoughts on “Ice in base of freezer”

  1. Hi Andy thanks for your reply. It’s supposed to defrost itself but by doing it manually we thought might cure the sheet of ice in the bottom of the freezer but it has returned. Do we have to pull the freezer out to get at the back of it or is there something inside the freezer?
    Regards, Sue

  2. I have a stand up deep freeze that’s almost the size of a regular fridge. It keeps getting frozen over on the back bottom (the back, not the inside back). Two of the lines get really frozen over and end up with 2 large white balls of ice. I have a photo if that would help. I currently have too much in it to unplug it and let everything melt and start from scratch.

    1. Andy Trigg (Whitegoodshelp)

      Hello Danielle. Send a quick email to me using my contact form at the bottom of this page. I can then reply to you and you can reply with your attached photo.

  3. Hello Andy,
    I have attempted to address the problem with your very helpful post.
    I could not remove the internal plate after removing the screws. The bottom had movement but the top would not give, even after a little hair drying.
    Its a Hotpoint.
    I applied heat blind under the bottom area and got some water out.
    I’m waiting to see if this worked, but wondered about the issue with the top.
    Many thanks
    Paul

    1. Andy Trigg (Whitegoodshelp)

      Hello Paul. I couldn’t say for sure, but maybe it was frozen with ice at the back. If you couldn’t take off the whole of the back panel the best thing would be to let it thaw out thoroughly with the door open for a minimum of 12 hours.

  4. Dear Andy
    I have just attempted to remove the back panel of my Liebherr Fridge Freezer due to ice build up. I am unable to do so due to the use by Liebherr of non standard screws (they appear to have six ‘grooves’ in the head instead of four). Did you have the same problem or were the screws retaining the panel in your freezer standard. Thanks for a very clear and enlightening article.

    1. Andy Trigg (Whitegoodshelp)

      Hello Roy. Those type of screws have been standard in most products for decades now. You can easily and cheaply buy screwdriver sets for them at any tool shop or places like B&Q, Wickes etc.

Leave a Comment

Your email address will not be published. Required fields are marked *

Comments Policy

Comments welcome (unless closed). Comments need to be on topic with the article (Moderated before appearing).


Scroll to Top